ASC Tradex

• Reduces opportunity for damage to formwork, extending usable life
• Minimizes cleaning of formwork before reuse
• Suitable for use with virtually all types of formwork

Additional Information:

• Item Code: 1258008

• Rapid strength gain.
• Vibration resistant.
• Corrosion resistant.
• Non-expansive.
• Can be placed underwater

• Precise composition
• No side effects
• Longer shelf life

Additional Information:

• Item Code: 1663010

Nitoprime 25 is a two component solvent containing primer consisting of modified epoxy resin based primer.

It is used in conjunction with Nitomortar, Nitoflor and Nitocote products.

• Easily applied by brush or roller.
• Long open time.
• High wetting out characteristics.
• High performance.

For sealing and maintenance of horizontal joints in concrete roads, concrete runways and hard standings. The excellentfuel resistance of Colpor 200 makes it particularly suitable for sealing areas where fuel and oil spillage might occur such as

Aircraft fuelling areas

Oil terminals

Garage forecourts

Parking and cargo areas

Docks and harbours

Warehouses

Cold applied - no heating equipment required

Fuel, oil and hydraulic fluid resistant

Self-leveling

Tough rubbery seal

High performance - less maintenance

Colpor 200 complies with U.S.Federal Specification SS-S

200E1984 and British Standard 52121990 - types N, F and FB.

Fosroc Colpor 200 cold applied, two part polyurethane sealant is designed for joints in concrete paved areas. The capability of accommodating cyclic movements is retained by Colpor 200 throughout extremes of temperature conditions.

Colpor 200 is resistant to fuel, oil and hydraulic fluid spillage, will not harden in cold weather nor become excessively soft or pick up in hot conditions. Colpor 200 has high durability and long service life which significantly reduces maintenance costs.

• Good adhesion to moisture, oil, bitumen
• Resisting to UV and atmospheric exposure
• Resisting against ozone and micro organisms

Additional Information:

• Item Code: 1138080

We are providing an excellent quality array of Cebex 100Admixture Chemical to our prestigious clients at very affordable rates within committed period of time.

High-flow, non-shrink, cementitious grout conforming to the requirements of BS EN 1504-3 Class R4 and BS EN 1504-6: Anchoring of reinforcing steel bar.
Conbextra GP is used for free flow, non-shrink, cementitious grouting of gap thicknesses 10 to 75 mm.

Non-shrink

High strength

Chloride free

Can be used at flowable or trowelable consistency

Features:

Long shelf life

Highly usage

Accurate composition

Excellent results

High effectiveness

Quick result

Available in :

0.227kg.

Additional Information:

• Item Code: 1046001

Conbextra EP75 is a solvent free epoxy resin grout designed for grouting of gap widths of 10 to 75 mm. It is supplied as a three component system consisting of base, hardener and specially graded aggregate. The components are supplied in the correct mix proportions designed for whole pack mixing on site.

• Creep resistant -to Improve resistance to deformation under constant loading.
• Excellent durability - high compressive, flexural and tensile strengths ensure a long working life.
• Cost effective - high early strength gain promotes minimum downtime and early commissioning of plant.
• User friendly - simple, full pack mixing to ensure that the performance characteristics are achieved.
• Versatile - suitable for a wide range of loading situations including repetitive dynamic loads.
• Excellent in service performance - non-shrink capability ensures full surface to surface contact.

• Quick response
• Precise composition
• Highly effective

Additional Information:

• Item Code: 1165002

Conplast SD110 chloride free admixture is specially formulated for optimum cost saving across a wide range of static and mobile (egg-laying) block paving and masonry production equipment. It is supplied as a brown solution which instantly disperses in water.

Conplast SD110 disperses the fine particles in the mix, improving cement dispersion and compaction to maximise the strength obtained from the cement used. The improved performance can then be used to allow reductions in cement content without loss of performance. Controlled air entrainment maintains yield and improves surface finish while providing improved resistance to frost attack.

• Strengths, density and yield of semi-dry concrete units can be maintained at lower cement contents.
• Allows higher early and later age strengths to be obtained without additional cement.
• Improves "green" strength, resulting in fewer losses due to breakage. Air entrainment improves resistance to frost attack.
• Improved mix cohesion allows economical use of a wide range of aggregates.

• 20 Ltr.
• 200 Ltr.

Additional Information:

• Item Code: 1293003

Conplast SP430 is a chloride free, super plasticising admixture based on selected sulphonated napthalene polymers. It is supplied as a brown solution which instantly disperses in water.

Uses:
To provide excellent acceleration of strength gain at early ages and major increases in strength at all ages by significantly reducing water demand in a concrete mix.
Particularly suitable for precast concrete and other high early strength requirements.
To significantly improve the workability of site mixed and precast concrete without increasing water demand.
To provide improved durability by increasing ultimatestrengths and reducing concrete permeability.

Advantages:
Major increases in strength at early ages without increased cement contents are of particular benefit in precast concrete, allowing earlier stripping times.
Makes possible major reductions in water:cement ratio which allow the production of high strength concrete without excessive cement contents.
Use in production of flowing concrete permits easier construction with quicker placing and compaction and reduced labour costs without increasing water content.
Increased workability levels are maintained for longer than with ordinary sulphonated melamine admixtures.
Improved cohesion and particle dispersion minimises segregation and bleeding and improves pumpability.
Chloride free, safe for use in prestressed and reinforced concrete.

• 20 Ltr.

Additional Information:

• Item Code: 1315008

• Nonpungent odor
• Balanced pH value
• Safe to use

Additional Information:

• Item Code: 1047007

Conplast AEA is a chloride free air entraining admixture based on neutralised vinson resin. It is supplied as a translucent water white coloured solution which instantly disperses in water.

Conplast AEA acts at the interface between the mixing water and cement/aggregate particles to produce microscopic air bubbles, which are evenly distributed throughout the concrete. The entrained air enhances durability by providing protection against the rapid temperature changes found in freezing and thawing conditions and with the use of de-icing salts.

Advantages:

• Air entrainment increases the resistance of concrete to attack by frost and de-icing salts, reducing problems of surface scaling and concrete failure.
• Entrained air bubbles assist in the formation of a stable cohesive mix, reducing segregation and bleeding.
• Air entrainment improves workability and helps produce a dense, uniform, close textured surface free from gravel nests and sand runs, so further enhancing durability.
• Excellent air bubble stability allows use with a wide range of aggregate qualities and mix conditions.

Conplast NC chloride-free accelerating admixture is supplied as a light straw-coloured solution that instantly disperses in water.

Conplast NC accelerates the early stages of cement hydration, producing more rapid stiffening and allowing strength gain to commence at an earlier stage. This effect is particularly noticeable at low temperatures and is most significant in the first 24 hours after mixing.

Advantages:

• Particularly effective in assisting to offset the delaying effect of low temperatures on setting and strength gain. 
• Accelerated setting gives added protection against early age frost attack.
• Also provides a degree of water reduction or increased workability.
• Suitable for use in bricklaying mortar.
• Chloride-free, safe for use in reinforced concrete.

Conplast WP90 powder is a fine, white powder ready for use with concrete or cement mortar mixes. Conplast WP90 powder is a traditional admixture to fill natural pores within the concrete or mortar matrix to reduce porosity and improve water tightness.

Advantages:

• Easy to use- Simple application familiar to site operations
• High Quality - Traditional waterproofing material manufactured to latest standards.
• Workability - Improves workability

• Chloride free, safe in prestressed and reinforced concrete
• Produces exceptionally high early strengths
• Plasticising action gives increased workability and/or increased strengths

Additional Information:

• Item Code: 1256003

• Excellent bond to the concrete substrate
• Shrinkage compensated
• Contains no chloride admixtures

Additional Information:

• Item Code: 2060002

Reebol Emulsion Xtra is supplied as a pale amber liquid which turns white when diluted with water to produce a chemical release agent, combining the outstanding release properties of such materials with the economy of a conventional oil. It reacts with the alkali in the concrete to form a thin water repellent skin on the surface of the mould which enables easy stripping from the hardened concrete.

• Non-staining : No cleaning of unsightly oil stains if plastering is not required.
• High quality : Produces really fair faced fi nish concrete.
• Versatile : Can be used on all types of moulds.
• Minimises cleaning : Makes cleaning of form faces between pours very easy.
• Concentrate form : Reduces storage and transport costs.
• Water based : Only requires water for dilution.
• Aids corrosion inhibition.

Additional Information:

• Item Code: 2169040

Conplast SP430 G8 is based on Sulphonated Napthalene Polymers and supplied as a brown liquid instantly dispersible in water.

Conplast SP430 G8 has been specially formulated to give high water reductions upto 25% without loss of workability or to produce high quality concrete of reduced permeability.

Advantages:

• Improved workability - Easier, quicker placing and compaction.
• Increased strength - Provides high early strength for precast concrete with the advantage of higher water reduction ability.
• Improved quality - Denser, close textured concrete with reduced porosity and hence more durable.
• Higher cohesion - Risk of segregation and bleeding minimised; thus aids pumping of concrete.
• Chloride free - Safe in prestressed concrete and with sulphate resisting cements and marine aggregates.

• 250Kg.

Form of Chemical:Liquid

Category:Waterproofing Coating

Brand: Fosroc

Additional Information:

• Item Code: 1315286

• Dust resistant
• No surface cracking or shrinkage
• Improves durability

Additional Information:

• Item Code: 1206302

Nitozinc Primer is supplied as a two component system based on metallic zinc and epoxy resin which on mixing gives a grey coloured liquid. Nitozinc Primer is recommended for priming exposed steel reinforcement for use with Fosroc concrete repair mortars. The product actively resists corrosion within the confines of the repair location and avoids the generation of incipient anodes in immediately adjacent locations. Nitozinc Primer is compatible with all Renderoc mortars and fluid micro concretes.

Advantages

• 1 Ltr
• 5 Ltr

Additional Information:

• Item Code: 2047040

Conplast X421IC is a dark brown liquid based on lignosulphonates which mixes readily with water and therefore disperses evenly.

Conplast X421IC waterproofs by improving the quality of the concrete or mortar. It reduces the water demand for required workability and minimises segregation and bleeding. Thus it is more effi cient compared to traditional powder waterproofs as its use results in two fold improvement of concrete or mortar.

Advantages:

• Liquid admixture: Instant and complete dispersion throughout the mix. Uniform waterproofing throughout concrete matrix.
• High efficiency: Dramatic reduction in permeability of concrete/ mortar
• Improved workability: Improves compaction of concrete and mortar, even where harsh sands or aggregates are used.
• Improved concrete quality : Minimises porosity and honey combing. Produces dense homogenous concrete.

• 20 Ltr.

Additional Information:

• Item Code: 1349018

Nitotile MPA tile adhesive is a high quality adhesive used for the permanent fixing of tiles over smooth surfaces such as existing tiles, ceramic tiles or glass, subjected to damp and tropical conditions and for specialised applications such as tile on tile and tile-on-glass etc.

Nitotile MPA is a single component, polymer modified cement based grey coloured powder.

• Polymer modified - prewetting of tiles not required and henceless prone to cracking of mortar.
• Single component - ease of application.
• Non toxic - User friendly application.
• Excellent adhesion on smooth surfaces - Develops high adhesive bond strength.
• Non shrink - excellent bond with the substrate.
• Excellent work and open wet time of 2 hrs at 300C - allows the mason to fi x tiles at ease even under hot conditions.
• Self cure - does not require external curing.
• Forms a dense and impermeable mortar bed waterproof.

Mould release agent for all kinds of formwork prior to concrete placement.  It is ideal for absorbent formwork, such as wood.

• To provide quick, clean and easy stripping of moulds and formwork.
• Ensures easy release, reducing damage and simplifying implementation.
• Minimises surface blemishes and staining, promoting high quality fair-faced concrete.
• Significantly reduces pore formation and surface air bubbles.

• 1 Ltr.
• 5 Ltr.
• 10 Ltr.
• 20 Ltr.

Additional Information:

• Item Code: 1334006

• No corrosive action
• Penetrates oil and grease
• Safe with metals except for zinc and galvanized steel

Additional Information:

• Item Code: 2167001

• Polymer based
• Enhanced cement hydration
• Superior control of moisture loss

Additional Information:

• Item Code: 1206404

Additional Information:

• Item Code: 2167022