ASC Tradex

Cold applied, high duty pavement sealant.

For the sealing and maintenance of joints in concrete roads, runways and hard standings. The excellent fuel resistance of Colpor 200 makes it particularly suitable for sealing areas where fuel and oil spillage might occur such as oil terminals, airfield hard stands and garage forecourts.

• Cold applied - no heating equipment required
• Fuel, oil and hydraulic fluid resistance
• Tough rubbery seal, tolerant of climatic variations
• Improved sealing efficiency - less maintenance
• High movement accommodation
• Two grades (pouring - self levelling and gun grade)

Renderoc S2 is supplied as a grey powder along with a liquid polymer and has to be mixed with water on site to produce a highly consistent, high strength repair mortar. The material is based on carefully blended cement, graded fillers and chemical additives and is polymer modified to provide a mortar with good handling characteristics, while minimising water demand. The hardened product exhibits excellent thermal compatibility with concrete and outstanding water requirement ensures fast strength gain and long-term durability.

• High strength
• Can be applied by hand, like conventional mortars
• Extremely low permeability provides maximum protection against carbon dioxide and chlorides
• Excellent bond to the concrete substrate
• Shrinkage compensated
• No site batching required, supplied in pre-weighed prepacked condition
• Only addition of water at site to be made while mixing the powder and liquid parts
• Contains no chlorides.

Additional Information:

• Item Code: 2234000

Renderoc RG Spl is supplied as a ready to use blend of dry powders which requires only the site addition of clean water to produce a free-fl owing non-shrink repair micro concrete. The material is based on Portland cements, graded aggregates and fi llers, and additives which impart controlled expansion characteristics in the plastic state, while minimising water demand. The low water requirement ensures high early strength and long-term durability.

For larger repairs, the mixed Renderoc RG Spl may be modified by the addition of 5mm to 12mm clean, graded, saturated surface dry aggregates at site. For exceptionally large repairs, the local Fosroc offi ce shall be consulted.

• Gaseous expansion system compensates for shrinkage and settlement in the plastic state.
• Can be pumped or poured into restricted locations.
• Fluidity to allow for placement without vibration.
• Pre-bagged to overcome site-batched variations.
• Rapid strength gain to facilitate early reinstatement.
• High ultimate strengths and low permeability of cured repair.
• Contains no chloride admixture.

Nitobond AR
Nitobond AR is a modified acrylic emulsion which is specially designed for use as a bonding aid, curing agent and gauging liquid for cementitious systems. It is resistant to hydrolysis and can therefore be used for external application.

Single component gauged as required.

Simply brushed onto concrete as a primer.

Provides excellent bond to concrete, masonry, stonework, plaster and block-board.

Improves tensile and compressive properties. Allows thin section applications.

Compatible with all common hydraulic cements.

Suitable for use in Middle East conditions. Used as a curing membrane.

Is economical in use.

Nitobond AR is a modified acrylic emulsion which is specially designed for use as a bonding aid, curing agent and gauging liquid for cementitious systems. It is resistant to hydrolysis and can therefore be used for external application.

Single component gauged as required.

Simply brushed onto concrete as a primer.

Provides excellent bond to concrete, masonry, stonework, plaster and block-board.

Improves tensile and compressive properties. Allows thin section applications.

Compatible with all common hydraulic cements.

Suitable for use in Middle East conditions. Used as a curing membrane.

Is economical in use.

Keeping track of latest market development we are devotedly engaged in offering the wide gamut of Nitobond AR. It is a modified acrylic emulsion which is specially designed for use as a bonding aid, curing agent and gauging liquid for cementitious systems. It is resistant to hydrolysis and can, therefore, be used for external application.

Features:

Single component gauged as required

Simply brushed onto concrete as a primer

Provides excellent bond to concrete, masonry, stonework, plaster and block-board

Additional Information:

• Item Code: 1703012

• Quick results
• Very effective
• Long shelf life
• Nitomortar S

Additional Information:

• Item Code: 1922000

Description:

Conbextra AT is a ready to use dry powder supplied in 25kg bags. Conbextra AT has been formulated specifically for grouting of bridge bearings and parapet post base plates. The addition of a controlled amount of clean water produces a free-flowing grout with high early and ultimate strengths as well as long term durability, suitable for use in section thicknesses 10mm to 100mm. Thicker sections can be achieved by incorporating clean, dry 10mm aggregate.

• Non-shrink
• High early and ultimate compressive strengths
• Good flow
• Low permeability ensures durability
• Can be poured or pumped

Conbextra GP1 is a non-shrink, free-flow, high strength cementitious grout. Machine base plate grouting - turbines, generators, pumps, presses, steel rolling beds, production machinery and crane rails. Construction grouting - stanchions, coloumns, beams, bolt pockets, keyways and anchors0. Aquaproof Anchoring Systems is authorised project Super stockist and brushbond authorised Fosroc applicator for Fosroc Chemicals(India) in Pune, Maharashtra and a leading dealer for construction chemicals.

High early and ultimate strength Free Flow Shrinkage compensation in plastic state Non metallic iron content Prepacked material

Advantages

• Non-shrink - Will continue to occupy the filled space without shrinkage. Continues to provide support to the bearing areas and dampens vibration.
• Free flow - Ensures high level of contact with load bearing area. Also helps complete filling without voids. No need for external aids like rodding, poking, chaining etc.
• Pre-packed and factory controlled - Consistency and reliability ensured. Site batching and blending variations eliminated.
• Iron free - No chance of deterioration by uncontrolled rust expansion, corrosion and staining of grout.
• Chloride free - Does not cause corrosion of machine parts, anchor bolts etc., in contact with grout.

• Lokfix is a two component polyester anchoring grout supplied in pre-measured quantities.
• The material cures quickly to give consistent, high performance anchorages.
• Version: Lokfix S25 - Blue lid
• Pourable grade, 25 minute gel time at 20°C for use in vertical down holes where the hole is 8 to 40 mm greater in diameter than the bar.

Advantages:

• Easy to mix and apply
• Rapid strength gain
• Vibration resistant
• Corrosion resistant
• Non-expansive
• Can be placed underwater
• Increased flowability
• Two grades specifically for vertical and horizontal / overhead use

Disclaimer: All visual elements of a product like color, texture, finish, pattern, design, shape, size, dimension and other such, as listed and displayed on www.buildmantra.com via image(s) and other multi-media content may differ from the actual due to variances in the type and quality of user's viewing screen/display monitor.

All product data provided on www.buildmantra.com are for knowledge purposes only. It is liable upon all those who use, handle or install any product listed on www.buildmantra.com to adopt safe product handling practices. Build Mantra is not liable for any injury /damage to any person /property /object /entity caused by the performance or non-performance of any product listed on www.buildmantra.com..

• Lokfix S: 0.5 liter
• The pack consists of a can of resin and a plastic bag of hardener contained in a plastic mixing pail with a snap-on lid.
• Store in accordance with the Highly Flammable Liquids and Liquefied Petroleum Gases Regulations 1972.
• Shelf life of 12 months at 20°C will be reduced at higher temperatures.

Uses

• Lokfix mix and place anchoring grouts are used for anchoring of steel bars into concrete, brickwork, masonry and rock.
• Recommended applications include:
• Installation of starter bars
• Base plate bolts
• MOT Bolts
• Installation of balustrades
• Installation of barriers and safety fences
• Installation of tie bars

• Store in accordance with the Highly Flammable Liquids and Liquefied Petroleum Gases Regulations 1972.
• Shelf life of 12 months at 20°C will be reduced at higher temperatures.

• Lokfix S25
• Using the calculated volume of grout based on the estimating guide table, the grout should be poured steadily into the prepared holes.
• The anchor bar is then pressed into the hole to the required depth; slight agitation will assist in achieving a complete bond.
• The bar should be left undisturbed in the required position until the resin is set.

Additional Information:

• Item Code: 1667000

Nitoproof 100 is a low viscosity blend of selected bitumens in solvent which dries to form a high quality tough bitumen film.

• Single component.
• Easily and inexpensively applied.
• Resistant to most naturally occurring chemicals.
• Does not taint water.
• Can be applied to damp concrete substrates.
• Quick drying.
• Excellent adhesion to most common building substrates.
• High coverage rates.
• Excellent water retention for use as a curing compound.
• Tough.
• Successfully used for over 30 years in a wide range of environments including Middle East.

Renderoc Plug provides an initial set time of approximately one minute.

• Emergency water-stopping capability.
• Single component - only the addition of clean water is required.
• Excellent bond to the substrate.
• Low exotherm minimises thermal cracking.
• Pre-bagged formulation to overcome variations in site batching.
• Contains no chloride admixture

• Nonpungent odor
• Balanced pH value
• Safe to use

Additional Information:

• Item Code: 2222003